Removing the Radiator

After a long long long break from doing anything, I've finally managed to start back on the car. I've decided to start removing the engine, doing a little bit whenever I get the chance.

The radiator was pretty easy to take out. First, drain the water (there's a tap at the bottom of the radiator - it was seized, but I think it's brilliant anyway), and then remove the bottom hoses...

...and remove the top hose...

...then undo the two retaining bolts on each side...

 

..then slide it out!

With the radiator now empty, there's the chance it might rust from the inside out. So to stop it rotting, I covered the pipe ends with the fingers from a marigold, then re-filled it with water and anti-freeze.

 

I was well-chuffed with myself for coming up with this idea. Unless I discover that the anti-freeze eats through the glove, the radiator rots anyway, and I've cut up a perfectly good pair of Marigolds for no reason.

Latest Update

I've not done much since the last update. Family, work and DIY have been a pretty good excuse to keep me out of the cold, apart from a couple of days where I was playing with some toys that I got for Christmas (trolley jack, imperial spanners, head torch).

I decided to use the trolley jack to lift the car to give me a better look at the underside of the sills/floor to see what needs doing, however this came with its own problems - the chassis legs. I was going to jack under the chassis legs until I realised that the nearside leg was shot...

Nearside chassis legs with obvious corrosion

---

Realising that the chassis legs will need replacing, I decided that this going to need a lot of clear space in the garage and plenty of access around the car. This also means removing the engine so that I can get into the engine bay floor and take the weight of those rotten sections. The recent cold snap has forced me to change the water in the cooling system, so have to leave the engine in for the time being, but I took the bonnet off anyway.

I didn't know if there was any coolant/anti-freeze in the engine, nor the last time the water had been changed. The engine is going to come out soon and it seems a bit pointless to change the water now, but it would have been a shame if the engine block had cracked due to neglecting this little job.

Changing the water also gave me an excuse to get the car started, and get it up to temperature - something that turned into a much bigger job than I expected. The battery turned out to be a bit of a dud, and even when connected to the battery charger, I needed the starting handle to get it going. The previous owner said the dynamo needed polarising, which also meant that the car couldn't even keep itself going once started - the car could only tick over using the power from mains electric!

Still it was really nice to hear the engine running, and the little burble from the exhaust. Considering the structural state of the car, it actually runs quite sweet - I really love these little cars! This was probably the last time it'll be running before it's taken out and rebuilt.

Current state of the car

UURRGHH, IT'S ASBESTOS!!

Aye, so I was sat at work and got to thinking about the heat shield beneath the passenger footwell (as you do). Then it suddenly dawned on me, "hmmm - I bet that's asbestos".

So I posted a question on the MMOC forum and yes, it is Asbestos - bugger. Apparently, it's white asbestos, and depending on its age, the clutch might be asbestos too, and the brake linings (at least when it was new) - but I knew this anyway.

The hole through the passenger footwell (the browny triangle)

---

The heatshield is mounted above the front baffle of the exhaust.

---

The white bit inside the heatshield is the asbestos.

---

Some of the members on the MMOC forum suggested that if its doing no harm, then leave it alone - but because you can see it through the hole in the floor and it might end up killing me, and anyone that rides in the car, I thought I better get rid.

I did a bit reading up on the actual dangers of asbestos, and the safest ways of removing it. I found the health and safety executive has a good section on asbestos at http://www.hse.gov.uk/asbestos/. I also spoke to the local council to see how to dispose of it, who recommended the following:

• Dampen the area down
• Wear protective clothing such as overalls (disposable preferably)
• Wear dustmask and gloves
• Avoid using powertools to reduce chance of breaking the material
• Dispose in double-bagged heavy-duty polythene bags, along with the overalls.
• Seal and label the bags
• Contact the council to arrange free disposal when next doing one of their "hazardous waste" pickups.

So following advice, I sprayed it with water to dampen down the fibres. Then taped over the hole in the floor, and taped a thick rubble sack to the underside of the car ready.

Once I was ready to catch the heatshield from underneath, I ground off the screw heads that were holding the heatshield on from the inside of the car. I would have preferred to unscrew them, but they were thick with gunk and wouldn't budge. After grinding the heads off, a swift whack with a mallet on the screws knocked them out and the heatshield fell onto the exhaust into the rubble sack I had taped to the underside of the car. I rolled this around the heatshield, then carefully double-bagged it in another two rubble sacks and taped them up. As recommended by the council, I did the same with the overalls I was wearing, and to be sure, my trainers aswell - they shouldnt have been binned years ago anyway.

Heatshield gone

I know it might seem a little over the top for what was just a little bit, but all of the research I did pretty much suggests to take no chances. I've just got to find something else to use as a heatshield now!

NEC Classic Motorshow

Went down to the Birmingham NEC for the Classic Motorshow this weekend, and had my pants pulled down by the parking charges. The Morris Minor Owners Club had their own stand there and had a few cars on show. This is pretty much the standard I'm aiming for with Arthur.

Took this as a reference point because the layout on mine will be similar (a bit different on later models)

Something like this for my next car would be class, but by the time I could afford it I'd look like one of those sad old buggers having a midlife crisis. Might have to aim lower - an MG, or a Triumph or something.

A good look at the sills

Today I finally managed to get the last of the kickplates/doors off to see how bad things were with the sills.

Nearside rear sill where it meets the rear wheelarch.

Thick packed mud has rotted away the rear wing and the floor.

---

More of the same on the offside rear.

---

For the record, those stupid "pig ear"indicators aren't original and are going in the bin eventually.

---

Pretty much the same as last time, but on the other side

Today I removed the nearside door and tried to remove the kick-plate but it was welded in place by an old repair. The floor pan is badly rotten where it meets the doorframe, and someone in the past has welded a steel plate on the underside to hide the rot from the M.O.T man. When they welded the repair panel, they also welded it to the kick-plate, and the door finisher (the rail that runs below the doors) which made it a bit of a pain in the arse to get off.

I removed the door finisher with a bit of grinding, which gave me better access to the welded edge of the kick-plate. More grinding and a bit of wacking with a mallet, finally got the kick-plate off...

It's hard to tell from this photo, but the condition of the box section isnt bad.

---

A tiny bit of corrosion towards the front, but its hardly anything. The door finisher removed is lying on the floor.

---

View from underside of the floor. The welded repair is the more rust coloured panel along the edge of the floor underside.

---

The nearside rear sill isn't too bad, considering the state of the kickplate that was covering it.

---

Still, could be easy to repair - if its worth it.

An inspirational kick up the arse

Since I found the holes in the floor a while ago, I've spent my time basically doing nothing. I was so pre-occupied with sorting the cross-member ends, that I had stopped everything while I planned and replanned how I was going repair them. This just overfaced me and nothing got done.

An inspirational kick up the arse from my dad made me realise that there is plenty I could be doing, so for the past few weeks I've been busy with an angle grinder.

Both front wings are shot, and have to go. The headlight surrounds are made of chicken wire and filler, and both wings are rotten all up the A-post.

---

The fixing bolts for the front wings are a little tricky to get to, and they're covered in over 50 years of muck, so I cut away large sections to give better access to the bolts.

---

There is a little corrosion along the top of the inner wing, but nothing massive. These can probably be plated over.

---

With the wing off, I could get a better look at the inner wing. The hole is where the jacking point for the car is supposed to be. Definitely need a new panel for this.

---

The left side doesnt have any corrosion along the top of the inner wing, but the jacking point and door post cover are badly shot.

---

Definitely need a new panel or maybe 2 for this.

Jacking point shot on this side too. A-Post cover plate very badly corroded too.

---

Both front wings off the car, and the bumper removed. Space to work is pretty tight, so just removing these is a massive help.

---

The silver (and rust) coloured plate is the kick plate. This covers a steel section that is important for the structure of the car, and is often corroded. I need to take this off to see what the state is.

---

Not too bad. There's definitely corrosion along the bottom of the section, but it could have been much worse.

---

Removed the drivers door to get a good look at the A-post. Everything looks alright as far as I can see, though I'll get a better idea when I remove the cover plate on the inner wing.

---

After removing the wings, I kept the light lenses and metal surrounds as these are still good (though would need re-chroming). I want to keep as much original as I can, especially since a lot of new replacements are not as good as recycled originals. I also cut a few sections from the front wings. Might come in handy for practice welding, or for plating over small areas.

---

...the rest waiting to be scrapped.